注: 建议图片大小150px*50px 
丨
English
注: 建议图片大小150px*50px 
 |
| Quantity: | |
|---|---|
Household Heating Systems Floor Heating Wired 6 Period Programmable Thermostat
Touch Screen Period Programming Thermostat Weekly circulation, it is possible to set 6 periods called events each day with corresponding pre-set temperatures, also you can select "period control mode" or "manual mode" according to your individual requirements.
Technical Data
| Power Supply | AC200-240VAC 50/60HZ |
| Accuracy | ±0.5ºC |
| Probe sensor | NTC |
| Power Consumption | <0.3W |
| Load current | 3A(water heating),16A(electric heating) |
| Temperature Adjustable Range | 5°C~60°C( can adjust to 35°C~60°C) |
| Limit Temperature Range | 5°C~60°C( factory setting: 35°C) |
| Output | Switch relay |
| Insulating condition | Normal environment |
| Running program | Set per 1 week as a cycle |
| Installation | Wall mounted |
| Application | Water Floor Heating System |
| Electric Floor Heating System | |
| Infrared Heater System | |
| Certificate | CE,RoHS |
Advanced setting (qualified person preferred)
You can press "M" and"Time"and hold for 5 seconds at the same time to enter the mode of advanced setting when the thermostat is turned off. The following seven function can be chosen by pressing "M".
| Symbol | Setting | Up or Down | |
| 1 | ADJ | Temperature calibration | Adjust measured temperature |
| 2 | SEN | Sensor mode | IN: built-in sensor |
| OUT: floor sensor | |||
| ALL: both sensors | |||
| (floor sensor is the limit sensor) | |||
| 3 | LIT | Limitation temperature | Adjust limitation value, |
| Limitation range:5℃~50℃ | |||
| 4 | DIF | Switching differential | Adjust switching differential |
| 5 | LTP | Antifreeze function | Turn on/off Anti-frozen function |
| 6 | PRG | Set vacation mode | 2: 5/2 day mode |
| 1: 6/1 day mode | |||
| 0: 7 day mode | |||
| 7 | RLE | Potential-free output | 00: in same way |
| 01: in different way | |||
| 8 | DLY | Potential-free output delay | Change the delay time |
| 9 | HIT | Max. Temperature | Max. Limitation temperature set point (99℃) |
| 10 | AFAC | Reset to factory settings | Programming parameters will be reset to factory settings when symbol appears |
Writing Diagram
Sensor Failure
Please select the right sensor mode when operation, it will display the "Err" symbol on screen far sensor failure, thermostat must be checked till the fault is eliminated.
| Packaging Details | UNIT WEIGHT: 0.35KG/PC; |
| 64 PCS/CTN; | |
| GROSS WEIGHT: 22.4KG; | |
| PAPER BOX PACKING; | |
| BOX DIMENSION: 42*40*29CM | |
| Delivery Detail | Shipped in 15 days after payment |
Installation Advice
All thermostat installations should be carried out by a fully qualified electrician.
To avoid electrical shock and to prevent damage to the thermostat,disconnect the power supply before beginning work.
Electrical wiring regulations prohibit the thermostats from being installed in bathrooms;if using the thermostat in a bathroom,install the thermostat on an internal wall outside the bathroom as close to matting power supply cables as possible.
Important
Do not switch on the system before the substrate(e.g.concrete)and floor covering(e.g.tile adhesive)are completely dry to avoid cracking.
Household Heating Systems Floor Heating Wired 6 Period Programmable Thermostat
Touch Screen Period Programming Thermostat Weekly circulation, it is possible to set 6 periods called events each day with corresponding pre-set temperatures, also you can select "period control mode" or "manual mode" according to your individual requirements.
Technical Data
| Power Supply | AC200-240VAC 50/60HZ |
| Accuracy | ±0.5ºC |
| Probe sensor | NTC |
| Power Consumption | <0.3W |
| Load current | 3A(water heating),16A(electric heating) |
| Temperature Adjustable Range | 5°C~60°C( can adjust to 35°C~60°C) |
| Limit Temperature Range | 5°C~60°C( factory setting: 35°C) |
| Output | Switch relay |
| Insulating condition | Normal environment |
| Running program | Set per 1 week as a cycle |
| Installation | Wall mounted |
| Application | Water Floor Heating System |
| Electric Floor Heating System | |
| Infrared Heater System | |
| Certificate | CE,RoHS |
Advanced setting (qualified person preferred)
You can press "M" and"Time"and hold for 5 seconds at the same time to enter the mode of advanced setting when the thermostat is turned off. The following seven function can be chosen by pressing "M".
| Symbol | Setting | Up or Down | |
| 1 | ADJ | Temperature calibration | Adjust measured temperature |
| 2 | SEN | Sensor mode | IN: built-in sensor |
| OUT: floor sensor | |||
| ALL: both sensors | |||
| (floor sensor is the limit sensor) | |||
| 3 | LIT | Limitation temperature | Adjust limitation value, |
| Limitation range:5℃~50℃ | |||
| 4 | DIF | Switching differential | Adjust switching differential |
| 5 | LTP | Antifreeze function | Turn on/off Anti-frozen function |
| 6 | PRG | Set vacation mode | 2: 5/2 day mode |
| 1: 6/1 day mode | |||
| 0: 7 day mode | |||
| 7 | RLE | Potential-free output | 00: in same way |
| 01: in different way | |||
| 8 | DLY | Potential-free output delay | Change the delay time |
| 9 | HIT | Max. Temperature | Max. Limitation temperature set point (99℃) |
| 10 | AFAC | Reset to factory settings | Programming parameters will be reset to factory settings when symbol appears |
Writing Diagram
Sensor Failure
Please select the right sensor mode when operation, it will display the "Err" symbol on screen far sensor failure, thermostat must be checked till the fault is eliminated.
| Packaging Details | UNIT WEIGHT: 0.35KG/PC; |
| 64 PCS/CTN; | |
| GROSS WEIGHT: 22.4KG; | |
| PAPER BOX PACKING; | |
| BOX DIMENSION: 42*40*29CM | |
| Delivery Detail | Shipped in 15 days after payment |
Installation Advice
All thermostat installations should be carried out by a fully qualified electrician.
To avoid electrical shock and to prevent damage to the thermostat,disconnect the power supply before beginning work.
Electrical wiring regulations prohibit the thermostats from being installed in bathrooms;if using the thermostat in a bathroom,install the thermostat on an internal wall outside the bathroom as close to matting power supply cables as possible.
Important
Do not switch on the system before the substrate(e.g.concrete)and floor covering(e.g.tile adhesive)are completely dry to avoid cracking.
